Paint is thin. A new coat of uniform color over a wall shows every dent, ridge and patch more clearly than the tired, uneven color it replaced, and a higher sheen shows them more again. That is why the preparation is where a painting job is really decided, and why it is the part a quick quote leaves out.
Most walls need some of the following before a brush comes out. Here is what each problem is, why it happens, and what a proper repair involves.
Nail pops
A nail pop is a small round bump or crack in the drywall where a fastener has pushed out. It happens as the framing behind the wall dries and shrinks over time, which leaves the nail standing proud of the stud. Filling over a popped nail just creates a bump that comes back.
The repair is to secure the drywall to the stud with a screw close to the old nail, set the old nail back below the surface, fill both, sand flush and spot prime. Once the sheet is held properly, the pop does not return.
Cracks at corners, ceilings and doorways
Hairline cracks running from the corners of doors and windows, along a ceiling line or down an inside corner are usually where drywall seams meet, and where a house moves most through the seasons. Smearing filler into a crack that keeps moving gives you the same crack again within a year.
- Cracked seams are cut out, re-taped and finished with joint compound so the joint is reinforced, not just filled.
- Inside corners where wall meets wall or ceiling often do better with a flexible paintable caulk than with hard filler, because the joint can move without cracking.
- Cracks in old plaster walls are opened up slightly, and loose plaster is reattached before the crack is filled, otherwise the repair moves with the loose section.
Wide cracks, cracks that keep growing, or doors that have started to stick alongside them are worth having looked at for movement in the structure before the cosmetic repair.
Holes, dents and old anchors
Picture-hanging holes and small dents take a lightweight filler, sanded flush once dry. Larger holes, such as those from wall anchors, a door handle or a removed fixture, need a backing: a mesh patch or a piece of drywall set into the opening, then layers of compound feathered out wide so the repair blends into the wall plane. A deep patch filled in one thick layer shrinks and cracks as it dries.
Before filling, it is worth deciding what is going back on the wall. Holes in exactly the right place for the same pictures and shelves can be left.
Why patches show through the paint
Filler and joint compound absorb paint differently from a painted wall. Paint straight over a patch, and it dries with a different sheen, a dull or shiny spot visible from an angle. This is called flashing, and it is the most common sign of a rushed repaint.
Every repair is spot primed before the finish coats so it takes paint the same way as the wall around it. On a wall with a lot of repairs, priming the whole wall is often the more reliable answer. Textured walls add one more step: the patch has to be textured to match before priming, or a smooth square will show on a textured wall.
When the whole wall needs primer and when spot priming is enough is covered in paint sheen, primer and coats.
Water stains
A brown ring on a ceiling or wall bleeds straight through ordinary paint, sometimes after it looks covered. It needs a stain-blocking primer before the finish coats. More importantly, the leak behind it needs to be fixed first. Painting over an active leak only hides the warning, and a stained area that has gone soft or sagging needs replacing, not painting.
Wallpaper residue and glossy surfaces
Two surfaces that paint will not stick to well without help:
- Walls where wallpaper has been removed. Leftover paste looks invisible, but paint applied over it can crack, wrinkle or peel. The wall is washed until the adhesive is gone, damaged paper facing on the drywall is sealed, and then it is primed.
- Glossy existing finishes, common on older trim and in kitchens and bathrooms. New paint needs something to grip, so gloss is scuff-sanded or deglossed and cleaned before priming. Kitchen walls near the range also carry a film of grease that has to be washed off first.
Caulk lines at the trim
Where baseboard, door casing and window trim meet the wall, old caulk shrinks, cracks and pulls away, leaving dark lines that a new coat does not hide. Failed caulk is cut out and the joints re-caulked with a paintable caulk before painting. It is a small step that makes the finished trim lines look crisp.
Older homes and lead paint
In homes built before 1978, older layers of paint may contain lead, and sanding, scraping or cutting them creates dust that is a health hazard. Repairs that disturb old paint in these homes call for lead-safe work practices, and lead abatement itself is work for a certified specialist. If your home is in that age range, it is worth raising at the estimate so the approach is decided before any sanding starts.
Planning a repaint
We write the preparation into the scope of every interior painting job: what gets filled, sanded, re-taped, caulked and primed. That way you can see what is included instead of finding out afterwards what was skipped. If new floors are in the plan too, the walls and trim are painted first; paint before or after new floors? explains why. Every project carries our lifetime workmanship warranty and a free 30-day return visit for touch-ups once the furniture is back. Book a free in-home estimate and we will walk the walls with you.